DIY: Giant Flowers

DIY Giant flower wedding

So many of you loved the giant flowers from Britney + Mark’s wedding that we asked Britney to share how she made those huge flowers and we are super excited to share the DIY with you all today! Britney did want me to share a little disclaimer that when they made these they never planned on creating a tutorial (but we are so happy you did!), so there is no exact science – just do what works for you, and if you have a great solution for one of the steps please share it! Big thanks to (once like a spark) photography for the photos!

• Several sheets of poster board (it takes at least two full sheets of poster board per flower)
• Large Plastic Solo Cups (1 per flower)
• Bath poof
• Hot glue gun and extra sticks
• Spray Paint
• Clear Plastic Wrap
• Thin wall electrical conduit, ½” x 10’. Home Depot SKU# 203106
• Halex ½” set screw connectors, Home Depot SKU# 839663
• Raco 3 ½” round cover, Home Depot Internet SKU# 202058390
• Wood Block or bucket filled with sand to help the flower stand up
• Fabric to pool at the base of your stems

Preparing the bath poof:
So we tried to use a whole poof…but it was just too much, so we cut it in half. There is a small rope that goes around the middle of the bath poof. Cut the poof in half leaving one side tied up by the rope. Keep a firm grasp on the rest of the poof. Add a generous amount of glue to the newly cut edge, then cover with a scrap of poster. Re-glue any places that are not secured. Do the same to the other half. Now you can make two flowers. Yay!

flower poof


Step one:
Lay the poster board glossy side down. (If the poster does not have a glossy side, it’s just fine.) Rip the poster towards yourself length-wise. Start by ripping pieces that are the entire length of the poster. I’m not going to lie, it takes a little practice to get a good technique.

After you get 5-7 very long petals between 2-4 inches wide, move on to tearing the smaller pieces. It’s good for the petals to curl, because they will begin to flatten out over time and you don’t want a droopy flower….or maybe you do!

Tip: Separate the petals based on size. You need several of each size, but more ofthe medium and small.

step one photo

petals in groups

Step Two:
Cut your cup in half. Then cut 1 inch tabs all the way around it. This will be your base. Hot glue your biggest petals to the OUTSIDE of the cut tabs. The weight of the petals should open the cup into a semi-flat shape.

step two

Step Three:
Continue adding petals to the INSIDE of the cup moving from largest to smallest. Be sure to fill in areas that look empty. Stop before you get to the smallest petals.

Step Four:
Glue your bath poof to the center. Once the bath poof is glued, add the smaller petals so that they curve up around it.

Step Five:
Once you are satisfied with the fullness of the flower, lightly dust the center with spray paint.
Tip:Guard the outer petals with newspaper or extra poster so they don’t get sprayed.

step five

Preparing the stem:
I’m going to be honest, my dad did this part – and there is no exact technique. Some have asked if PVC pipe would work. We tried it, but it was too flimsy. Instead, we used thin wall electrical conduit from the electrical department at Home Depot. You also need a screw connector and a round metal outlet cover. If you are confused, print out the picture, take it to the home improvement store and they should know exactly what you need.

Bending the conduit (stem). THIS is the difficult part: Hold the pipe up at an angle, one end resting on the ground. Slightly bend by stepping on the lowest section, move your foot up 8-10” and repeat until you have the curve you want. Be careful and don’t try to bend the conduit all at once, making numerous smaller bends works best. Once the conduit is curved, attach the Halex screw connector onto the flower end of the conduit, knock the center plug out of the Raco round cover plate and secure it to the screw connector (very easy, just sounds confusing).


Option 1: Drill a 7/8” inch hole in a large piece of wood. Insert the bent conduit stem (as seen below).
Option 2: Use buckets filled with gravel or sand to keep the flower upright.
Option 3: Simply push the stem into the ground if your event is outdoors.
Option 4: Make something up. If it works, share your wisdom with the rest of us!



Wrap the conduit in several layers of clear plastic wrap. It actually looks better if it’s a little messy.

Finally, attach the completed flower using a lot of hot glue to the 3 ½” cover plate. You will need A LOT of hot glue. And just when you think it is secure, add more glue…just in case. You don’t want the wind taking off with the top of your flower! Now pool your fabric around the base (you can see this in her ceremony photos below) and –Viola! You are finished!!

DIY Giant flower wedding

And a few photos from their wedding to see how they used them for their pretty outdoor ceremony –be sure to check out their entire wedding feature here!

DIY Giant flower wedding

DIY Giant flower wedding

DIY Giant flower wedding

Big thanks to Britney for putting this together for us and to (once like a spark) photography for the photos!

Interested in advertising with us?

for our current rates!


  1. I was a bit skeptikal at the beginning of the blog, but these actually look very nice!

  2. What a fantastic idea! Thank you so much for making a tutorial- cannot wait to give it a try.

  3. i fell in love with these flowers since you posted their wedding, so glad you shared de DIY…i will definitely make some myself.

  4. WOW! I must say that’s really some coolest works I’ve experienced so far in my life. Making wedding decoration stuffs using poster board and others is really amazing. I’ll share this interesting with my buddies to impress them. I like these works. Thanks

  5. Can’t help but crack up at using a bath poof as the center of the flower, but it really works! And it’s gorgeous. Thanks for a fab DIY.

  6. thanks so much for posting this diy! love the flowers and can’t wait to try for my own wedding!

  7. I am totally doin this!! I will be trying out different colors though to make a more dimensional effect. thank u so much for a very detailed DIY!! :)

  8. A briliant decoration to have, really effective.

  9. I loved this so much. I had already made the ginormous rose for my Mom’s 70th birthday party and was thrilled when I saw this. It definately gave me some good ideas for the stem, and I think I have a better way now for the stem. Try using a 5′ PVC conduit with a 1/2 elbow piece. Then I took a 4″ square cover and put that on the elbow and locked it all together with a 1/2 locking piece. DONE sooo much easier. I will post pics of mine when I get done with ALLL the flowers I’m making for the party!

  10. I live in the uk and struggled to find the fixings. However, my lovely boyfriend fashioned stands from copper pipe, and also from broom handles, with pieces of plywood screwed on to fix the flowers to. I also used a paper plate and a shed load of hot glue fixed behind the paper cup for added stability. I made them in sunshine yellow for a colleagues wedding, then in white for a garden party. Also did a couple of mini flowers for wall hangings. They are very easy and look spectacular. Loved making them and can’t thank you enough for the idea!

  11. I tried this during the week and unfortunately mine didn’t quite turn out as shown in the photos. I think I’ll revisit this again on the weekend.

  12. Some people are so incredibly creative. I think I’ll give the big flowers a try tomorrow.

    Thanks so much for sharing this.


  1. […] wedding dresses ♥ Palm Springs Elvis wedding! ♥ Tattooed bride & a SmogShoppe wedding ♥ Giant paper flowers DIY ♥ This Alice in Wonderland book art is AMAZING ♥ This close to home handmade wedding is just […]

  2. […] top left clockwise: DIY Giant Flowers via Green Wedding Shoes / DIY Giant Paper Flowers from Ruche via Design*Sponge / Giant Paper Poppy Flowers via Martha […]

  3. […] freaking cool are those DIY giant flowers? Perfect for an outdoor […]

  4. […] tutorial which you can find at Green Wedding Shoes seems quite advanced, especially when it comes to the stand but this a fantastic effect, I am very […]

  5. […] – Giant Flowers…an amazing way to decorate a wedding […]

  6. […] and Favour – From DIY Wedding MagazineRope Wedding Words – From DIT Wedding MagazineGiant Flowers – From Green Wedding ShoesHow To Make Your own Pom Pom Place Settings – From Love my DressDIY Ombre Pinwheels – […]

  7. […] Green Wedding Shoes shared this DIY tutorial on how to make the giant […]

  8. […] gigantic paper flowers by Green Wedding Shoes at this couple’s ceremony […]

  9. […] paper flowers at the next real wedding was featured on Green Wedding Shoes and the DIY can be found here. The chair garland is a simpler way to add this feature to your decor and this particular one was […]


Email me when there are new comments on this post. You can also subscribe without commenting.

GWS is a creative and supportive community of wedding fans and vendors. As such, we reserve the right to remove comments that contain profanity, are distasteful, personally attack individuals or do not contribute to the goals of our community.

You may not love every detail of every event, but please remember that the couples who share their weddings on GWS are real people and their wedding is a special day, so please be nice.